Visonic POWERMASTER-10 - INSTALLER GUIDE Specifikace Strana 73
- Strana / 82
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
APPENDIX C. Detector Deployment & Transmitter Assignments
72 D-303222 PowerMaster-10/30 G2 Installer's Guide
B2. Common Areas
Common areas are areas used as walkthrough zones to areas of 2 or more partitions. There may be more than one
common area in an installation depending on the layout of the property. A common area is not the same as a partition;
it cannot be armed / disarmed directly. Common areas are created when you assign a zone or zones to 2 or 3
partitions. Table A1 summarizes the behavior of the different zone types in a common area.
Table A1 – Common Area Definitions
Common area zone types
Definition
Perimeter
Acts as defined only after the last assigned partition is armed AWAY or HOME.
In case that one of the partitions is disarmed, an alarm initiated from this zone is
ignored for all assigned partitions.
Delay zones
Delay zones will not trigger an entry delay unless all assigned partitions are armed.
It is, therefore, not recommended to define delay zones as common areas.
Perimeter follower
Act as defined only after the last assigned partition is armed AWAY or HOME.
In case that one of the partitions is disarmed, an alarm initiated from this zone is
ignored for all assigned partitions.
In case that one of the common area assigned partitions is in a delay state (and
the other partitions are armed), the alarm will behave as a perimeter follower for
this partition only. The event will be ignored for other assigned armed partitions.
Interior
Acts as defined only after the last assigned partition is armed AWAY.
In case that one of the partitions is disarmed or armed HOME, an alarm initiated
from this zone is ignored for all assigned partitions.
Interior follower
Acts as defined only after the last assigned partition is armed AWAY.
In case that one of the partitions is disarmed or armed HOME, an alarm initiated
from this zone is ignored for all assigned partitions.
In case that one of the common area assigned partitions is in a delay state (and
the other partitions are armed), the alarm will behave as an interior follower for this
partition only. The event will be ignored for other assigned armed partitions.
Home / Delay
Acts as a Perimeter-Follower type when all assigned partitions are armed AWAY.
Acts as a Delay type when at least one of the assigned partitions is armed HOME.
Will be ignored when at least one of the assigned partitions is disarmed.
Emergency; Fire; Flood; Gas;
Temperature; 24-hour silent;
24-hour audible; Non-alarm
Always armed.
APPENDIX C. Detector Deployment & Transmitter
Assignments
C1. Detector Deployment Plan
Zone
Zone Type
Location
Chime (melody
Sensor
Holder
No.
Default
Programmed
Default
Programmed
Location) or Off (*)
Type
1
Delay 1
Front Door
2
Delay 1
Garage
3
Delay 2
Garage Door
4
Perimeter
Back Door
5
Perimeter
Child Room
6
Interior
Office
7
Interior
Dining Room
8
Perimeter
Dining Room
9
Perimeter
Kitchen
10
Perimeter
Living Room
11
Interior
Living Room
12
Interior
Bedroom
13
Perimeter
Bedroom
14
Perimeter
Guest Room
15
Interior
Master Bedroom
- INSTALLER GUIDE 1
- PowerMaster-10/30 G2 2
- Version 16 2
- Installer's Guide 2
- 1. INTRODUCTION 4
- Figure 3.2 –Phone Wiring 10
- 3.4 GSM Module Installation 11
- 3.5 PGM-5 Installation 12
- Figure 3.6a – Cable Wiring 13
- Figure 3.7a - Power Cable 15
- Connection 15
- Figure 3.9 - Final Closure 17
- Figure 4.3a – Phone Wiring 19
- Figure 4.6 21
- Figure 4.9a –Expander Module 23
- Figure 4.9b – Zone 24
- and Siren Wiring 24
- 4.11 Battery Insertion 26
- Figure 4.13 27
- 5. PROGRAMMING 28
- [1] in Step 1 above) 29
- 5.2.2 Selecting options 29
- or 30
- 5.4 Zones / Devices 31
- Part B - Configuration 32
- - Configuring New Devices 33
- 5.4.3 Deleting a Device 35
- 5.4.5 Replacing a Device 35
- 5.5 Control Panel 37
- VOICE REPORT 39
- SMS REPORT 39
- 5.6 Communication 44
- String Editor Functionality 47
- Voice <- -> C.S 51
- Ringback time 51
- Ambient level 51
- Mast. UL/DL code 53
- Inst. UL/DL code 53
- 5.7 PGM Output 54
- Zone B Z:_ _ 55
- Zone C Z:_ _ 55
- 5.8.2 Record Speech 56
- 5.9.3 Testing the GSM module 58
- 5.10 User Settings 59
- 5.11 Factory Default 59
- 5.12 Serial Number 59
- 5.13 Start UL/DL 60
- 5.14 Partitioning 60
- 5.15 Operation Mode 60
- 5.15.3 BS8243 Setup 61
- 5.15.4 DD243 Setup 62
- 6. PERIODIC TEST 63
- <location> 65
- 7. MAINTENANCE 66
- 7.4 Fuse Replacement 67
- 8. READING THE EVENT LOG 68
- APPENDIX A. Specifications 69
- A2. Wireless 70
- A3. Electrical 70
- A4. Communication 71
- A5. Physical Properties 71
- (optional) 72
- Assignments 73
- APPENDIX D. Event Codes 75
- D2. SIA Event Codes 76
- APPENDIX E. Sabbath Mode 77
- APPENDIX F. Glossary 78
- Compliance with 80
- Standards 80
- WARRANTY 81
- PowerMaster-30 G2 82
Související produkty a manuály pro Bezpečnostní systémy pro řízení přístupu Visonic POWERMASTER-10 - INSTALLER GUIDE
(9 stránky)© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.040 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce