Visonic POWERMASTER-10 Uživatelská příručka Strana 24
- Strana / 76
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
REVIEWING TROUBLES AND ALARM MEMORY
D-303223 PowerMaster-10 / PowerMaster-30 User's Guide 23
Clearing the Memory Indication
To clear the ‘Memory’ indication you must first review the cause of alarm as described above. Once you return
to the ‘Ready’ screen simply press Away
and enter the code if requested, then press Disarm
followed by the code. The memory message will now clear. Otherwise the memory indication and content will be
cleared upon the next arming of the system.
Troubles
A. Indication of Trouble condition
If the system detected a trouble condition in any of the enrolled devices, the TROUBLE indicator illuminates, 3
beeps are sounded once per minute and a flashing TRBL message is displayed, as follows.
READY HH:MM
(alternating)
READY TRBL
or, if the system is not ready for arming -
NOT READY HH:MM
(alternating)
NOT READY TRBL
B. Displaying Trouble Information
All trouble messages need to be reviewed and corrected as described below:
EXAMPLE: The kitchen device - zone No. 9 - has reported a low battery – the living room device zone No. 15 -
has been inactive, and an attempt to communicate a message to your telephone has failed. However, these
troubles do not prevent the system from being “ready to arm”.
To review the source of the current troubles one by one, click the button repeatedly as shown below:
PRESS RESULTING DISPLAY
POWERMASTER-10
∗
Z09 LOW BATTERY
(alternating)
Z09 CONTACT
(alternating)
KITCHEN
↓
Z15 MISSING
(alternating)
Z15 MOTION SENS.
(alternating)
LIVING ROOM
↓
COMM. FAILURE
↓
READY HH:MM
∗
When working from the PowerMaster-30 control panel, the display will read "PowerMaster-30".
- PowerMaster-10/ 1
- PowerMaster-30 1
- Table of Contents 2
- INTRODUCTION 10
- Basic Arming and Disarming 11
- Arming ‘AWAY’ 12
- Arming ‘HOME' 12
- Disarming and Stopping Alarm 12
- Forced Arming AWAY or HOME 13
- Arming in the Latchkey Mode 14
- Disarming under Duress 15
- Using Keyfob Transmitters 15
- Initiating Alarms 16
- Initiating Emergency Alarm 17
- Siren Alarms 17
- Chime ON/OFF 17
- SPEECH AND SOUND CONTROL 19
- ELECTRICAL APPLIANCE CONTROL 21
- Troubles 24
- General Indications 25
- MENUS AND FUNCTIONS 26
- USER CODES 27
- Z04: BYPASSED 30
- ALREADY ENROLLED 40
- 12:40 PM 41
- button 41
- 30.12.2007 42
- 12:00 PM 43
- PRIVATE REPORT] option 44
- (- - - - - - ......) 53
- Event notifications by SMS 53
- Remote Control by Telephone 53
- Remote Control by SMS 55
- TESTING THE SYSTEM 57
- "NO EXISTING DEV 59
- <OK> TO EXIT 59
- MAINTENANCE 60
- APPENDIX A. PARTITIONING 62
- APPENDIX B. GLOSSARY 65
- FCC STATEMENT 69
- New Devices 70
- Abort Fire Time 70
- UDP/TCP Protocol Selection 70
- 24H Zone Report 70
- Record Speech 71
- Operation Mode 71
- BS8243 Setup 72
- DD243 Setup 73
- Smoke Siren Test 74
- Using the User Code 75
- ☺ Go to step 4 75
Související produkty a manuály pro Bezpečnostní systémy pro řízení přístupu Visonic POWERMASTER-10
(96 stránky)Vantec ION 2 VAN-460N manuali
Manuali dei proprietari e guide per l'utente per Attrezzi Vantec ION 2 VAN-460N.
We fornisce 1 manuali pdf Vantec ION 2 VAN-460N per scaricare gratuitamente in base al tipo di documento: Manuale Utente
Komentáře k této Příručce